AudioCodes Mediant 600 Bedienungsanleitung Seite 411
- Seite / 568
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Version 5.4 411 May 2008
SIP User's Manual 7. IP Telephony Capabilities
7.3.2.2 Collecting Digits Mode
When automatic dialing is not defined, the device collects the digits.
The SIP call flow diagram below illustrates the Collecting Digits Mode.
Figure 7-3: Call Flow for Collecting Digits Mode
7.3.2.3 Ring Detection Timeout
The ini file parameters IsWaitForDialTone and WaitForDialTone apply to Ring Detection
Timeout. The operation of Ring Detection Timeout depends on the following:
No automatic dialing and Caller ID is enabled: if the second ring signal doesn’t arrive
for Ring Detection Timeout, the device doesn’t initiate a call to the IP.
Automatic dialing is enabled: if the remote party doesn't answer the call, and the
ringing signal stops for Ring Detection Timeout, the FXO releases the IP call.
Ring Detection Timeout supports full ring cycle of ring on and ring off (from ring start to ring
start).
- User's Manual 1
- Table of Contents 3
- List of Figures 10
- List of Tables 14
- Reader's Notes 16
- Trademarks 17
- WEEE EU Directive 17
- Customer Support 17
- Related Documentation 18
- 1 Overview 19
- 1.2 Mediant 600 20
- 1.3 SIP Overview 21
- 2 Configuration Concepts 23
- 3 Web-Based Management 25
- 3.3.1 Toolbar 28
- 3.3.2 Navigation Tree 29
- 3.3.3.1 Accessing Pages 32
- 3.3.3.2 Viewing Parameters 32
- 3.3.3.5 Working with Tables 36
- 3.3.5 Working with Scenarios 40
- 3.3.5.3 Editing a Scenario 43
- 3.3.5.6 Deleting a Scenario 46
- 3.3.7 Getting Help 52
- 3.3.8 Using the Home Page 52
- Red: Fan tray failure 57
- 3.3.8.5 Replacing Modules 61
- 3.4 Configuration Tab 64
- [2] PassThrough = N/A 67
- [0] Auth NULL 75
- [1] Auth UNIX (default) 75
- [0] = OAMP 75
- [1] = Media (default) 75
- [0] = OAMP (default) 77
- [1] = Media 77
- [2] = Control 77
- 3.4.2 Media Settings 80
- [2] Bypass 84
- [3] Events Only 84
- 3.4.3 PSTN Settings 96
- 3.4.4 Security Settings 111
- 3.4.5 Protocol Configuration 133
- [0] Disable 135
- [1] Supported (default) 135
- [2] Required 135
- [1] Enable = Enable 143
- [1] Enable = Enabled 150
- [1] SRV = SRV 150
- [2] NAPTR = NAPTR 150
- 3.4.5.1.3 Proxy Sets Table 153
- 5 steps: 154
- 3.4.5.1.4 Coders 157
- • x: Any single digit 163
- 3.4.5.2.3 Metering Tones 182
- 3.4.5.2.5 Keypad Features 184
- 4 steps: 189
- [9] Private = Private 196
- 3.4.5.6.1 Authentication 219
- 3.4.5.6.2 Automatic Dialing 220
- 3.4.5.6.4 Call Forward 222
- 3.4.5.6.6 Call Waiting 225
- Disable (default) 232
- 0 = Disable 234
- 1 = Enable 234
- [0] 0 = ROUTINE (default) 241
- [2] 2 = PRIORITY 241
- [6] 6 = IMMEDIATE 241
- [8] 8 = FLASH-OVERRIDE 241
- 3.4.6 Advanced Applications 244
- [1] Alaw = Alaw (default) 252
- [3] MuLaw = MuLaw 252
- 3.5 Management Tab 253
- 3.5.1.3 Maintenance Actions 262
- 2 steps: 265
- 3.5.2 Software Update 266
- 6 steps: 271
- 3.6.2 Gateway Statistics 283
- 3.6.2.2 Call Routing Status 286
- 3.6.2.3 Registration Status 287
- 3.6.2.5 IP Connectivity 289
- 4 ini File Configuration 291
- 4.2 The ini File Structure 292
- 4.3 Modifying an ini File 296
- 4.4.2 System Parameters 305
- [10] = 100000 307
- [1] = Enable RAI service 307
- [0] = Disabled (default) 313
- 4.4.4 Security Parameters 314
- 4.4.5 RADIUS Parameters 320
- 4.4.6 SNMP Parameters 321
- [0] Disable (default) 326
- [1] Enable 326
- [1] = Enabled 332
- 4.4.9 Voice Mail Parameters 343
- 4.4.10 PSTN Parameters 344
- [1] = User-to-User 350
- [0] = Disable (default) 355
- [1] = Enable 355
- 4.4.14 Channel Parameters 377
- 5 Default Settings 385
- 6.5 Coefficient File 393
- 6.6 Dial Plan File 393
- 6.7 User Information File 395
- 7 IP Telephony Capabilities 397
- 7.2.2.1 T.38 Fax Relay Mode 399
- 7.2.2.5 Fax Fallback 402
- 7.2.3 Supporting V.34 Faxes 404
- 7.3 FXO Operating Modes 406
- 7.3.1.2 Two-Stage Dialing 408
- 7.3.1.4 DID Wink 409
- 7.3.2 Telephone-to-IP Calls 410
- Connectivity and QoS) 415
- 7.7.4 Relevant Parameters 416
- 7.9 Call Detail Record 417
- 7.13 Configuration Examples 423
- PSTN, take this step: 431
- 7.14.3 Call Transfer 438
- 7.14.4 Call Forward 439
- 7.14.5 Call Waiting 440
- 7.14.7 Caller ID 441
- 8 Networking Capabilities 445
- 8.3.1 STUN 447
- 8.4 IP Multicasting 448
- 8.9 VLANS and Multiple IPs 450
- Control: Premium control 453
- Management: Bronze 453
- 9.1 Clock Settings 459
- 9.2 Release Reason Mapping 459
- 9.2.1 Reason Header 460
- 9.3 ISDN Overlap Dialing 463
- 9.4 Using ISDN NFAS 464
- 9.4.1 NFAS Interface ID 465
- 10.1 Conference Server 469
- 10.1.1.1 SIP Call Flow 470
- 10.1.1.5 PSTN Participants 472
- 10.2 Announcement Server 483
- 10.2.2 MSCML Interface 484
- 10.2.2.1 Operation 485
- 10.2.2.6 Relevant Parameters 491
- 10.3 IP-to-IP Transcoding 494
- 11 Tunneling Applications 497
- 11.2 QSIG Tunneling 500
- 12.1 OSN Server Modules 501
- 12.2 Required Working Tools 502
- 13.1 Requirements 509
- 13.3.1 Cabling 519
- 14.1 Requirements 523
- 14.2 Cabling 524
- RedHat™ EL 4+) 534
- 14.5 Installing Linux™ SUSE 544
- 16.1 Mediant 1000 557
- 16.2 Mediant 600 561
- 17 Glossary 565
- Terminal Equipment (ISDN) 567
- Voice Prompts (File) 567
Verwandte Produkte und Handbücher für Gateways / Controller AudioCodes Mediant 600
(46 Seiten)
(44 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.139 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern